Boss Grill 6 Burner Built-In Gas BBQ - Stainless Steel

Hi, The manufacturer requires a minimum 1 metre (1000 mm) clearance at the rear of the Boss Grill IQBBQINT6 for safe ventilation, gas safety compliance, and maintenance access. Although the lid may open with less space, installation with reduced rear clearance is not recommended or compliant with the official guidance.

Thank you.

Hi, The Boss Grill 6 Burner Built-In Gas BBQ (IQBBQINT6) is configured for use with LPG (propane or butane) only. It is not suitable for connection to natural gas in its current setup. Natural gas requires different burner orifices and a lower-pressure regulator. Using this BBQ with natural gas without proper conversion could be unsafe and may damage the appliance.

Thank you.

Hi Phil,No, this BBQ is designed for bottled LPG gas and is not intended to be connected directly to mains natural gas. It would require a proper conversion kit and a Gas Safe engineer, and in most cases this model is not supported for conversion, so it should be used with a gas bottle instead.Thanks!

Hi, The Boss Grill IQBBQINT6 uses 304 stainless steel for the burners and cooking grates. The BBQ body is stainless steel construction, as per the manufacturer specification.

Thank you.

Hi, The rotisserie on the Boss Grill 6 Burner Built-In BBQ mounts internally within the unit, with the motor attaching to one side and the spit rod supported across the cooking chamber, so it does not require any additional height above the BBQ. Because of this, the difference between a 700 mm BBQ installation height and 900 mm adjacent worktops does not affect the rotisserie function or installation. The only requirement is that there must be no overhead obstruction and sufficient clearance for the lid to fully open safely.

Thank you.

Hi, The Boss Grill IQBBQINT6 requires a 610 mm cut-out depth for the unit itself, however it must be installed with at least 1 metre of clear, unobstructed space to the rear and sides in accordance with the manufacturer’s safety instructions. The final installation design must therefore allow sufficient rear clearance for safe lid operation and ventilation, and the cooking surface height alignment is controlled by installation height, not depth.

Thank you.

Hi, For safe use and maintenance of your Boss IQBBQINT6 6-Burner Built-In Gas BBQ, you must allow at least 8–10 inches (20–25 cm) of space at the back so the drip tray can be fully removed for cleaning. Additionally, the manufacturer recommends a minimum of 1 metre clearance at the rear for safety. Installing the BBQ directly against a wall would prevent proper drip tray removal and could compromise safety.

Thank you.

Hi Jake,The LEDs on the Boss Grill 6 Burner Built-In Gas BBQ (model IQBBQINT6) are powered by batteries, not mains electricity, so no external power supply is needed for the lights.Thanks!

Hi, The gas for the Boss Grill 6 Burner Built-In Gas BBQ (IQBBQINT6) connects at the rear of the unit, not the front knobs. The front controls only operate the burners. The gas line and regulator attach at the back before installation and are hidden once fitted. Always follow the installation instructions or use a qualified installer.

Thank you.

Hi Alan,To drain excess fat and oils from the Boss Grill 6 Burner Built-In Gas BBQ (IQBBQINT6), first allow the grill to cool and ensure the gas is off. Remove the built-in drip tray or grease cup located beneath the cooking area, pour out the collected fat safely, and wash the tray with hot, soapy water before replacing it. Regularly trimming excess fat from meat, monitoring flare-ups while cooking, and cleaning residual grease after each use will help prevent grease fires and keep the grill functioning efficiently.Thanks!

Hi Alan,Yes — the Boss Grill 6 Burner Built-In Gas BBQ does have a drip tray, and it pulls out from the rear of the grill (i.e., it slides out the back for emptying and cleaning).Thanks!